Skip to main content
Training & Workouts

How your weekly TSS (training load) target is set

How IntervalCoach decides how much you can train each week: CTL-based targets, ramp-rate limits, progressive overload, periodization, and the settings you can fine-tune.

Written By Martijn Russchen

Last updated 17 days ago

One of the most common questions is: how does IntervalCoach decide how much I can train in a given week? Here is exactly how the weekly TSS (training load) target is set, and how you can shape it yourself.

It starts from your fitness (CTL), not your FTP or VO2max

The weekly load target is anchored to your CTL — your 42-day rolling training load (the "Fitness" number on your dashboard). CTL is the best available answer to "how much can this athlete absorb right now," because it already reflects exactly what you personally have been training, week after week.

Your FTP and VO2max are deliberately not used to set volume. They describe how strong you are, not how much load you currently tolerate. FTP still drives your zones and the intensity of each workout — it just is not what decides your weekly hours.

In short, each week's target is sized to move your current fitness along the ramp toward your goal. Training a little above what your current CTL sustains is what actually nudges fitness upward over time.

Once you have a few weeks of history, the starting point for each week is what you have actually trained: the median of your last three weeks of TSS, plus 20% room to grow. The load that holds your current fitness (CTL × 7) is the floor, so one easy week does not drag the target down.

What happens with no training history

If you are brand new and there is no history to learn from, the system does not guess from population averages or last year. Your first week is anchored to your current fitness (roughly 1.5x your current weekly load), and the plan ramps up from there. The starting point is always "where you actually are today," never an abstract target dropped on you. If you have already proven you train more than that, your demonstrated volume wins and the cap steps aside.

Capped by the time you have available

The weekly target is also bounded by how much training time you have told IntervalCoach you have. The plan never sets a target higher than your available hours can hold: it takes the hours on your Training Volume schedule and multiplies them by the training load you typically generate per hour. So your weekly target is essentially the smaller of "the load your goal needs" and "the load your available time allows."

This is the most common reason a weekly target looks too high. If your schedule says, for example, three hours every day (around 19 hours a week), the plan assumes you can absorb that and sizes the week to it, even if you usually ride less. To bring it down, lower your daily durations on Training Plan > Training Volume so they match what you actually train, and the target drops to match. Your demonstrated training can raise this ceiling when you consistently train more than your schedule suggests, but it will not lower it.

If you would rather not manage durations day by day, there is an advanced option that does it for you. On the Training Plan page under Schedule, open Workout duration and choose "Coach chooses the duration." That treats the time on each day as a maximum and lets the coach pick the most effective length itself, often shorter, instead of filling the whole slot, so an easy or recovery day no longer stretches to your full available time.

How fast it is allowed to climb

Week-to-week increases are capped by a ramp rate. How fast the plan may climb follows the Training Demand setting on the Training Plan page:

  • Easy builds conservatively.

  • Moderate, Demanding and Aggressive all build at the same moderate pace. Demanding and Aggressive make every week of the build heavier, because Training Demand also scales your weekly targets, but they do not make the climb steeper.

If your goal needs a big jump in fitness, the plan stretches the build across more weeks rather than overloading you in any single week.

Your CTL target means race-day fitness

The number you pick in the CTL target wizard is the fitness you will have on race morning, not a peak you touch somewhere mid-plan. Internally the plan builds to a slightly higher peak, and the taper then deliberately sheds a little fitness so you arrive fresh. Goal progress compares your projection against that same race-day number, so a taper that is tracking exactly as designed no longer reads as falling behind.

Progressive overload

Because the early ramp weeks sit below your goal, the plan keeps track of the load you "missed" during the ramp and adds it back as a small overload in the later weeks, slightly above your goal — just enough that you still accumulate the total stress needed to reach your target fitness, instead of falling short.

You can also verify this is actually happening: the Analytics page has a Progressive Overload view that compares similar workouts week over week, so you can see whether your sessions are genuinely getting harder over time, not just whether the plan intended them to.

What happens when you fall behind

Life happens, and the plan re-reads reality every week. Each weekly refresh re-anchors the target to your actual fitness and your recent demonstrated load, then eases it back toward your goal over the following weeks instead of piling the missed load on top. A lost week lowers the starting point and the ramp re-plans from there. If the race-day goal drifts out of reach, the CTL target wizard is the place to re-check what is realistic.

Periodization shapes the curve

On top of the ramp, the weeks are not flat. Build weeks rise, then a recovery week pulls volume back (typically to somewhere between 55% and 75% of the base, depending on the model), and as a race approaches the plan tapers. So your weekly-TSS line climbs in steps, with regular easier weeks baked in, and dips into each race. The week after an A or B race is always planned as a recovery week, wherever the mesocycle stood.

Setting your own target for a week

On the Training Plan page you can click a week's TSS target and enter your own number. That week then reads set by you, with the plan's own number next to it (for example plan 450). Back to the plan undoes it.

  • Future weeks only. You cannot set the week you are in, or a week with an A or B race: race week follows its race-week taper.

  • Your number stays. It is kept when the plan refreshes each week and when you use Rebuild plan.

  • The sessions follow. Setting a target starts a rebuild of the sessions toward your number. The sessions may not add up to it exactly.

  • It uses a rebuild. Setting a target counts as one of your 3 plan rebuilds per rolling 24 hours, the same allowance as the Rebuild plan button.

Fine-tuning it yourself

None of this is locked. If you think like a coach, you can shape the model and let the system handle the week-to-week bookkeeping:

  • Periodization model (Settings > Goals) — linear, undulating, block, polarized or pyramidal.

  • Recovery depth — how much recovery weeks cut back.

  • Mesocycle length — 3 to 6 weeks.

  • Taper profile — aggressive, standard or conservative.

  • Training methodology (Settings > Training) — standard, Norwegian singles, Norwegian doubles, or the Easy Interval Method.

  • Age bracket (Settings > Training) — optional and self-reported. Masters athletes get more recovery-conscious planning: more spacing between hard days and a lower weekly intensity ceiling.

  • Training Demand (Training Plan page) — Easy, Moderate, Demanding or Aggressive. It scales your weekly targets, and Easy also slows the ramp.

Why it works this way

The design avoids inventing a number for you. It reads what you have actually done (CTL), starts there, limits how fast it is allowed to grow, and lets you reshape the model if you disagree with it. Training age is handled implicitly: a beginner has a low CTL and a veteran a high one, so the ramp naturally starts from each person's real level.